Just How To Install A Bathtub (For Newbies).
Just How To Install A Bathtub (For Newbies).
Blog Article
The publisher is making a number of good points relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content which follows.
Installing a tub isn't exactly brain surgery, but it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably challenging task. If the old tub is readily obtainable, the job can relocate immediately; if you have to open up a wall to eliminate the old tub and also place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub and embeded in the new one. Make certain you have qualified on your own for the work and fit trying it. Rather than employing a contractor to take over a halfway-completed task, it is much better to take into consideration employing one before you begin. Possibilities are you might need an expert plumber to make tube links.
This write-up will assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and don't need to alter the setup of your previous water pipes.
Your tools as well as material checklist ought to make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Before moving on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the faucet in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the called for placement. The wooden boards are practical in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the tub till the spirit level reads degree.
To mount taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the tub must wait up until the bath tub has actually been made use of at the very least once as this will certainly resolve it right into its final position.
Preparing for the Installation
Firstly, the supporting framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture fairly very early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were guided to that article about Installing A Bathtub through someone on a different web property. Sharing is nice. One never knows, you may just be helping someone out. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Information Report this page